Hello
I'm more used to asking practical questions, but now I'm stuck
I have version 11 of Solidworks , I changed my PC
I tried to load SLDW with the DVD the setup blocks me
when you click on it the sldlM asks me for permission to modify on my pc, after the yes
The disk starts and stops , back to square one.
I sent an email to Visiativ , no answer!!
What should I do
Hi @ LARGHETTO
The problem arises it seems to me but without knowing since you don't give the info
The version of Windaube if you're in 10 or 8 I don't think it works
If you have W7 it should work
What did you take as a PC and system?
@+
Hello
Now it's window 10 before I had the 7 then the 8
from a laptop I switched to a tower with 1 terra and 8 GB of ram
Finally the 10 is installed now, should I downshift?
That's not fun
Kind regards
I read via Google searches that it could still work
in theory w10 is compatible with the mini SW 2015 sp5
according to my readings
And what did you take as a proc ?
@+
Hello
SW 2011 is not compatible with Windows 10, but with Windows 7.
Attached is the link detailing all this: link
Cdlt
Good evening
First of all, thank you for your answers
Yes a priori, I read well in the properties
that compatibility was Windows 7
however I installed Sldw 4 years ago on a laptop, it was w7 ok
But in 2018 or early 19 I switched to W8
and in early 2020 Windows 10
and during all this time I never had a problem with SLDW even with these Windows changes
So I find it hard to understand
What do you think?
Kind regards
Your PC config is not great for SW
look at this link for installation issues
https://www.visiativ-solutions.fr/problemes-solidworks-microsoft-mise-jour/
Test drive and give news
@+
Sorry gt22 I don't understand your sentence
"Your PC config is not great for SW"
can you explain to me
Thank you
Larghetto83
Given the configuration of your pc it's not optimized for solidworks
It's not a workstation suitable for solidworks
not convinced that your graphics card is in the criteria and solidworks approved
(your configue is not great)
Oops.... forget the step ;-( in my previous message
Have you looked at the links I posted?
@+
Thank you for your answer
yes I looked at the Visiativ doc
I created "install" in window following their instructions
HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\Installer (Note: If the "Install" folder does not exist, create it. Right-click on the "Windows" folder then New/Key).
but do I really have to register the 32-bit Dword key
whereas we are going to work in 64 bits????
Oops, unrecorded message, empty party
I will start my answer again
Yes I read the visiativ tutorial,
I created the "install" directory but I'm skeptical about the key
they indicate Dword 32 bits,
why not Qword 64 bits???
See more on page 2
To conclude, I am recommended:
Finally, go to the SOLIDWORKS administrative image folder and restart the StartSWInstall.hta (to perform a SOLIDWORKS repair ).
Where is the so-called administrative image, to find the famous StartSWInstall.hta file
In any case thank you for your help
Larghetto
Hello
StartSWInstall.hta is not found in the administrative image
isn't it purely and simply the SETUP ??
My config not being "great" for SLDW is this a reason for the config not to launch?
SW11 on W10, that's a lot of lag.
It is possible that on the old machine, the Windows version changes did not cause a problem but that the direct installation on W10 cannot be done.
Before considering a return to W7, if you can, try running the install on a blank W7 machine.
Be careful that there are no more updates for W7,
Generally speaking, you may also have problems installing for Office.
The administrative image installation is a special installation procedure, dedicated to companies with a network: the image is hosted on a server and deployed on the user machines by the system administrator.
In your case, you must only apply the 1st part of the Visiativ procedure (individual installation).
Thank you for your answer
I will work in this direction and keep you informed
Kind regards
Larghetto