Hello
I'm coming back to the charge about my printing problem under Draftsight.
It's been more than a year since I have been able to print with the Draftsight software. I've tried all the versions, several different printers, but nothing works...
I have to print dxf in bulk, so I downloaded the 2015 version, telling myself that it will finally solve the problem. Of course not....
I don't know what to do to print under this software....
Help-me!
This subject had already been addressed by me in this question:
http://www.lynkoa.com/forum/3d/draftsight-probleme-impression
But it was never solved...
Have you already managed to print with it at the beginning?
Have you tried a complete uninstallation, then delete the registry (or clean with CCleaner for example) and then re-inset?
Yes, it's a crazy story, I've been on this problem for + a year.
I'm trying again anyway, I may have missed something....
Otherwise, there is an unstoppable order!
Go to a DOS window and write format c::-D then re-establish Windows!
But you lose all the info on your C drive! To be used with full knowledge of the facts!
Joking aside, there are 2 solutions here:
One person says that he uninstalled a software, but doesn't remember which one and it worked afterwards.
Another deleted all printers (making a front screen print to reset them) with the following command from start run:
PRINTUI /s /T2
Note: I don't know about this command more info here: http://technet.microsoft.com/en-us/library/ee624057.aspx
Then reinstalled the last drivers and it worked.
Source: http://www.eng-tips.com/viewthread.cfm?qid=364734
And have you seen this subject?
http://www.lynkoa.com/forum/3d/je-n-arrive-pas-imprimer-avec-draftsight
Well there I uninstalled everything, I made a ccleaner, I also removed the keys from the registry.
I restarted, I went back to admin mode. I believed it to death!!!! Of course not.
Always the same....
I'll try what you offer me
Well, I deleted a lot of software that I didn't use anymore.
I did a new ccleaner job, I uninstalled the printers which were useless.
Re ccleaner.
Draftsight reinstallation: same problem!!!!!!!!!!!!
I'm going crazy
Hotline?
WWWWWOoOOOUUuUuUU !! =)
Finally!!!!
I managed to print!! 1 year for that, I'm really bad.
Then:
- I had several old printers installed. (some with errors)
- When I wanted to delete them, windows deleted them, but after a refresh (F5), they kept coming back...
- Actually, I had documents queued in these printers and that's why windows didn't delete them.
So I cancelled all the documents waiting for all the printers, then I was able to delete them.
Re-install Dratfsight and there.................... =) Complete happiness
Honestly, I've been on this problem for more than a year and you solve it in an hour:p
Thank you Lucas! I'll pay you a shot;)
Glad I was able to help you!
For the drinks, it should be fine, I have 96 bottles coming soon!
FYI @Benoit.LF : Axemble (MyCADServices) does not support DraftSight... I don't know if other SolidWorks resellers support it.
Ooooh :o Is that petty:p ^^
And for the record, I'm not a customer of Axemble
FYI, I've already had answers about Draftsight from my reseller. Who is not Axemble. Will I have found the first positive point of my dealer? :)
Hello
Axemble is able to inform you about DraftSight, they even do training on it.
@+
@Bart: There was no pettiness in my remarks!
@Coyote: thanks for the info, I asked a few years ago and was told that the support didn't take care of Draftsight!
Well, so no positive point for my dealer :/
It's just a joke Lucas =)